Owning a European car may present you with a great image, but it may cost more for maintaining that persona. Keeping the vehicle’s warranty updated is one of the main elements to remember. The cost of repairs will be significantly more expensive in the United States.
Be sure to read the owner’s manual and understand how important it is to continue all maintenance on the vehicle. Maintaining the scheduled procedures can make the difference in a great running car and one that isn’t, for more than one reason. European cars might have different maintenance plans required versus an American made vehicle. Therefore, the warranty will provide extra coverage for the repairs.
It takes special tools for European vehicles, so it is important to go where a specialist, like the ones at Wolfe’s Foreign Auto, can do correct maintenance to ensure the warranty specifications are met. The dealership will also be able to locate the parts needed to do repairs. Experienced technicians have more skill for a foreign car and can do the job much quicker.
It is not advised to install used parts on the vehicle. Aftermarket parts can be used for American-made vehicles and other vehicles not manufactured in Europe. Those parts may not work sufficiently on your car. At the time of installation, they may save money but in the long-term, money will be saved by using the correct part.
Different standards are set within the United States versus European standards. Different grades are placed on the units concerning the viscosity ratings. A viscometer measures how fast the flow runs through a device. Using American oil can damage the European motor car.
Special additives with specific properties are used and must meet the ACEA standards. These oils are difficult to locate, and more than 90% of the ones on the American market are not sufficient. Sludge can develop and cause engine failure.
The main thing to remember is not driving when the car is almost out of gas. The fuel pump is located in the fuel tank in European cars. Therefore, the car should not be driven if it is low on fuel. The pump can receive damage and need replacement if this happens.
European cars have other elements that make them have more charm. However, American cars tend to cost a lot less to maintain within the United States. Understanding the differences in cost of repairs and other standards must be considered before you decide to park that fancy European car in your driveway.Learn More
Did a collision leave you with damage to the windshield of your vehicle? A prompt repair of the glass is the best thing that you can do, as a cracked windshield can interfere with your safety in a collision. In this article, learn a few reasons why you shouldn’t drive your vehicle when the windshield is cracked.
You Will Feel More of the Impact in a Collision
One of the best safety features of a windshield is the protection it can provide if someone hits you in the front of your vehicle. Rather than you and everyone else inside of the vehicle possibly suffering serious injuries, a large amount of the impact won’t make it to the cab area. Basically, a good windshield will help some of the impact go into the chassis of your vehicle instead of the cab area. The chassis is the front hood area of your vehicle where the motor, engine and other vital parts are located. It is a good idea to get a damaged chassis repaired so that you are more protected if you are involved in another collision.
The Structural Stability of Your Vehicle is Compromised
You must understand that the windshield is more than a piece of glass that keeps objects out of your vehicle. The windshield is actually an important part of the structure of your roof, as it gives it more strength. If you drive with a cracked windshield and get into an accident that causes your vehicle to rollover, it is more likely that the roof will cave in on the cab area where you and your passengers are located. A good windshield can prevent severe roof damage in a rollover accident, which may protect you and your passengers from injuries that can be fatal.
Airbags May Not Function Properly in a Collision
If you have a cracked windshield, your air bags may not be able to protect you as well as they should during a collision. The reason is that the airbags will usually deploy and hit the windshield as a way to keep you inside of the vehicle, which can possibly cause the windshield to crack. When airbags deploy against a cracked windshield, the glass is likely to shatter and it is possible that you or your passengers will be ejected out of the vehicle. Take your vehicle to an automotive collision center to get the windshield fixed as soon as you are able to!Learn More
Replacing the windshield in your passenger truck requires that you take special care when operating your vehicle in the first couple of days post-installation. The new windshield was installed using a waterproof sealant that needs time in order to thoroughly cure and dry.
By preventing the windshield from moving while the sealant is drying, you can proactively keep the new windshield from leaking as it ages in place. The best thing that you can do to avoid damaging the sealant on your trucks new windshield is to not drive your truck at all for at least a day after installation. If possible, you should park your truck in a shady area out of the direct sunlight, where the windshield sealant will have the ability to dry slowly and evenly.
If you must drive your truck in the days immediately following the installation of a new windshield, then you should do the following things to help prevent possible damage:
Stay Off of These Types of Roads
When your truck’s windshield is only days old, you should make every effort to avoid:
You must avoid highway driving because the higher speeds that are associated with freeway driving place a lot of force onto the new windshield. Excessive force moves the glass in its wet seal and will lead to leaking in future years. Gravel roads and those with potholes also can cause the glass to move around in the new seal. Roads that are very dusty will cause the dust to adhere in the sealant in a way where it cannot be cleaned off in the future and will detract from the clean look of your windshield.
Open a Window to Prevent Pressure Problems in the Cab
If you do not roll down a window in your truck before you close its door, then some pressure will be built up inside of the cab whenever you close a door. While this pressure is fairly small and not a problem with an existing windshield, a new windshield’s seal can be affected by the outward pressure caused by closing a door. To avoid this, you must roll down a window in your truck while the windshield’s seal is curing. You should also avoid slamming the doors as this can move the windshield in its new seal also. Click here for more information on auto glass replacement.Learn More
Your car’s paint is more delicate than you think. You need to be very cautious on what lands on it; some seemingly innocent actions may cause permanent damage. Here are examples of four things that may damage your car’s finish:
Parking Near a Construction Site
If you regularly park near a construction site, you will soon be paying for new car paint. This is because concrete may land on and damage your car. The alkaline compounds in the cement react with the paint and cause fade marks. Wet concrete isn’t that difficult to remove, but it gets complicated when it dries and can cause permanent paint damage. In fact, trying to remove it may even cause further damage when you scrape off some of your car’s paint with the concrete.
Writing Wedding Messages on Car Windows
While you budgeted for every little detail of your wedding, you probably didn’t include car damage. Many people consider it a norm to write “Just Married” on the back window after the wedding. This is not bad, but it’s the common writing materials, shoe polish or shaving cream, that complicates the issue. These materials can be nearly impossible to remove when they stray onto the paint. Be careful with your writing or use a safe alternative, such as a sticker, which is easier to remove.
Parking Under a Tree
Parking under a tree may seem like a clever move since it prevents the sun from damaging your car’s paint or heating up the interior. Unfortunately, you may just be swapping one form of damage for another if you park under a tree. This is because bird droppings and tree sap can cause considerable paint damage.
Damage from birds’ droppings occurs because the paint lacquer contracts and hardens around the droppings. As for tree sap, it comprises of many different compounds that eat through the car’s finish and etches the paint.
Using a Generic Cleaner on Your Car
Generic cleaners may work on most things, but they aren’t designed for your car. For example, using dishwashing detergent to clean your car isn’t a good idea since it is designed to remove everything from the surface of the object being washed. Therefore, if you use dishwashing detergent on your car, you will be stripping the protective polymers off the surface of the paint, which accelerates paint fading.
Many things can damage your car’s paint; it’s best to err on the side of caution if you aren’t sure whether a substance can damage it. Contact your auto repair shop as soon as possible if a foreign substance lands on your car’s paint, and you don’t know how to remove it safely. Prevent permanent damage by acting fast.Learn More
Moving parts eventually wear out on semi-trucks and will have to be replaced. A common problem that develops after tens of thousands of miles on the road is that the clutch will typically wear out. You need to get to a mechanic shop right away so they can replace the old clutch with a new one, and you can get back on the road to make money. This is a job for the experienced mechanic with the right set of tools. Here is a brief overview on how a mechanic will replace the clutch on a semi-truck.
Step 1: Remove Transmission
The mechanic has to remove the transmission to gain access to the clutch assembly on a semi-truck. The truck is raised in the air on a truck lift. A hydraulic jack is placed under the transmission to support the weight of the transmission while the mechanic unbolts it from the clutch assembly. The transmission will stay on the jack when the mechanic moves it to the side so he can work on the clutch.
Step 2: Remove Clutch Assembly
The clutch assembly is removed in the following order:
Installing New Transmission
Here is how a mechanic will put the transmission back together.
Main Flywheel: The main flywheel is typically resurfaced and checked for deformities. The flywheel is placed back onto the truck and bolted to the crank flange. Blue thread lock is placed onto the bolts to protect the bolts against rust and corrosion. The thread lock also prevents the truck’s vibrations from loosening the bolts.
The bolts are tightened using a torque wrench to manufacturer’s specifications.
Two threaded studs are placed at the top of the flywheel into the holes where the clutch will bolted later in the process.
Release Bearing & Captive Disc
The mechanic will place an alignment tool through the center hole in the release bearing and captive disc (the release bearing is built into the captive disc).
A non-captive disc is placed over the alignment tool with the flywheel side of it facing away from the captive disc. The assembly is then slid over the two threaded studs on the main flywheel to hold it in place as the mechanic installs the mounting bolts through the clutch assembly and into the main flywheel – blue thread lock is used on these bolts, too.
The two threaded studs are removed after all the other mounting bolts have been installed. Mounting bolts are then placed where the threaded studs were located. These bolts are also tightened according to manufacturer’s recommendations with a torque wrench.
The alignment tool is removed once all the parts have been securely bolted in place.
New brake pads are placed over the input shaft on the transmission and clipped into place. The transmission is then raised and the input shaft is slid into the clutch assembly. The mechanic then bolts the transmission housing to the clutch housing.
After the mechanic has reinstalled the transmission onto the clutch, he can then proceed to adjust the clutch so everything works well to get your truck back on the road.
To learn more about semi truck repair, contact a company like Arizona Fleet Service.Learn More
If you drive a manual transmission vehicle, you are in charge of when your transmission shifts into a different gear. Because you are doing this manually, there could potentially be a higher chance of you experiencing transmission damages, as you won’t likely be as precise and constant when changing gears like an automatic vehicle would. If you run into transmission problems, you will want to know of these defects immediately, so you can avoid major transmission problems down the road. A few signs that can help inform you of transmission issues are below:
Hesitation When Shifting Gears:
Over time, the friction layer on your gears will become to deteriorate, which will make the surface of your gears a bit slippery. This will make it a bit more difficult for your clutch to grab onto your transmission flywheel, which can cause hesitation when shifting into a higher or lower gear. If this sign is presented it can mean that it is time that you take your car into a mechanic shop and have your clutch replaced, as this can definitely be a sign that it is time for a new one.
Vibration Feedback When Shifting Gears and Shakiness:
Has your shifting stick ever given you a vibration feedback? Or has your car rattled a bit after shifting into a different gear? If you have experienced either one of these issues, then there could potentially be a cracked gear in your transmission. A cracked gear can be a bit more serious than a slipping clutch, so you will definitely want to have a mechanic replace your cracked gear sooner, rather than later, as this will prevent further complications from arising.
Burning Smell After Driving:
Have you recently taken your car for a spin? If you have and notice a burning smell after getting out, then this could mean that your transmission fluid is bad. Like your engine oil, your transmission fluid can become too hot and begin to burn. This can prevent your transmission from receiving the correct about of lubrication, which can cause friction. The old fluid and the friction that your transmission has can result in a burning smell. If you notice a burning smell coming from your transmission then be sure to have a local auto shop flush out your old fluid and replace it.
These indicators won’t only inform you of potential defects that your transmission may have, they will also allow you to respond quickly to these signs, which can help you avoid the costly expense of having your transmission rebuilt. Visit Karry’s Automotive Service Center for transmission repairs.Learn More
Purchasing a fleet of commercial trucks for your business can be an expensive undertaking, but there are a few things you can do to mitigate the expense. Use these tips to save money as you shop for the commercial equipment you need to keep your business on track.
Negotiate Your Insurance Rates
Commercial truck insurance carriers may be willing to offer you several discounts that can save your business a significant amount of money. You can get up to 20 percent off of your premiums for trucks that require CDL licenses for operation by providing proof of your CDL-class license. If you choose to pay your annual premiums in advance, you could qualify for a 5 to 15 percent discount, depending on the individual insurance carrier. Ask about bundle discounts and multiple vehicle discounts that can offer even more savings. Shop around and find the carriers that are willing to offer a combination of excellent coverage and competitive discounts to get the best value for your insurance dollar.
Buy Used Instead Of Leasing New
Leasing a new truck lets you stock your fleet with brand new equipment without having to pay the full sticker price for each truck, but the costs over time can be significant. With a new leased truck, you’ll have to pay for miles put on each truck in excess of the lease agreement. If your company sees an increase in business, you may end up having to pay a lot for the mile overages. When you buy used, you can still finance your purchase, but the costs will be lower and you won’t have to pay any additional fees once the vehicles are paid off. Buying used can help your business see significant savings over leasing or buying new vehicles.
Diesel engines tend to have a longer lifecycle than gas engines, which can save you money in the long run. The typical diesel engine can deliver 300,000 miles of dependable use in a medium-duty truck while a gas model offers around 200,000. Your fuel costs may be a bit higher with the diesel engine, but you won’t have the cost off replacing your engines as often.
Investing in a fleet of commercial vehicles lets your company stay competitive with other area businesses. Use these helpful tips to help save some money on your fleet and make your company more profitable for years to come.Learn More